Skip to content

Steps To Replace Automobile Battery.

Typical indications that a battery is about to fail are headlights dimming, sluggish starting,just recently having needed to jump start your automobile, alternator troubles, electrical troubles.

If you failed to see or there were no giveaways of your automobile battery failing and you end up being stuck at home, it might be worth looking for a mobile automobile battery replacement service close by.

On the other hand you may want to replace the automobile battery by yourself. The following is general advice on how you can do it yourself. Before you attempt to change it, Its advised to examine the automobile makers guidance for your particular automobile.

If you have no experience replacing a automobile battery, or your automobile has exclusive demands like battery registration, you may be better to get an mobile car battery replacement expert to do the job for you.

Before replacing your automobile battery you should understand that most modern automobiles can be very electrical reliant and may store settings for windows, roofs, stereos and other electrical components.

In the event that your automobile battery has already died those settings may already have been lost or if you remove your battery without an external power back up you may lose these settings.

Automobiles installed with Stop/Start systems or that have special charging systems that control the power level from the alternator to battery, require brand new batteries to be registered with the automobile.

These battery registration tools are not cheap, and whilst you may manage to take the automobile to a local service centre that has the tool, they may well not be prepared to register the new battery as they did not install it.

In case your automobile is installed with the new AGM kind battery it should be replaced with the very same kind and not a standard lead acid kind as this will often times result in electronic troubles and premature battery malfunction.

Make certain you confirm you have the appropriate automobile battery for your automobile prior to trying to changing it out, the majority of batteries come with a label probably on the top or side that contains the battery kind, battery amps, and battery cranking on it.

Battery Installation Method

Action 1 All the things switched Off.

Confirm all of the your automotive electrics are switched off and automobile keys are taken out from the ignition.

Action 2 Find the automotive battery.

Depending on your auto kind the following are some of the most typical battery places, underneath the bonnet, seats, and in the boot region.

Action 3 Take away battery clamps.

Your battery may possibly have a clamp across the top or a small clamp at the bottom fixing the battery into place. These are normally held down with 8mm,10 mm, or 13mm bolts or nuts, a lengthened socket and bar set might be require.

Beware as automobiles age the brackets can easily get corroded, which might consist of having to change the battery tray. (Spray some easy release substance on in cases were they look rusty).

Action 4.Connect External Power.

Attach the battery memory saver to the automobile if your automobile configurations have not already been lost due to a failed battery. Always comply with the tool makers information on the best technique to do this.

Action 5. Disconnecting The Old Auto Battery.

Whenever you remove the dead battery, if you have a battery memory saver fastened the battery terminals will certainly still be powered.

When unfastened, you will have to make sure that the terminals do not come into contact with another metal surface. Upon removing endeavour to cover these using a non conductive material.

Most automobile battery terminals use 8mm,10 mm,13 mm nuts these can generally be undone with a spanner.

Disconnecting the terminals.

(Negative Terminal 1st).

The initial terminal to take off will be the negative that has the - (minus) icon on it or the battery area itself.

(Positive Terminal 2nd).

Then take off the positive terminal that has the + (plus) sign on it or the battery itself.

When you have the terminals unhitched transfer them out of the way so you have full easy access to extract the battery (ensure not to allow the removed terminals to touch anything).

Certain auto batteries can additionally have a gas venting out line connected, this should be unfixed before removal.

Action 6. Hooking up the new automobile battery.

Ensure that the battery place is clear and tidy, then make certain the battery terminals are out of the way and position the automobile battery back into its location.

(Attach the Positive Terminal 1st).

Remove the non-conductive cover from the positive battery terminal and hook on to the positive terminal on the battery. Verify it is pushed down and re tighten.

(Secure the Negative Terminal 2nd).

Remove the non-conductive cover from the negative battery terminal and attach to the negative terminal on the battery. Make sure to secure and afterwards re tighten, if you have a battery vapour venting pipe reconnect to the new battery.

Action 7. Detach the external power/battery memory saver.

Any time you are happy that your new auto battery is fastened you may now detach the battery memory saver device. (Do Not Switch on Or Start the automobile with the battery memory saver still hooked up).

Action 8. Start the automobile.

You are able to now start the automobile to check all is functioning as soon as you are happy the new battery is hooked up and the battery saver is detached.

Action 9. Refit the battery brackets.

Once you have started the automobile and are happy all is ok refit the battery brackets making sure you do not make connection with the battery terminals.

Action 10.Stop/Start and Batteries Requiring Registration.

Automobile batteries that involves battery registration you may now link the battery registration equipment and perform the operation.


No Trackbacks


Display comments as Linear | Threaded

No comments

The author does not allow comments to this entry

Add Comment

Form options